Exactly How to Remove and Change a Tub
Exactly How to Remove and Change a Tub
Blog Article
What're your thoughts and feelings about How to Install a Bathtub?
Mounting a bathtub isn't exactly rocket science, however it does require solid plumbing, woodworking, and also occasionally, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably difficult task. If the old bathtub is conveniently obtainable, the job can move speedily; if you have to open up a wall surface to get rid of the old bathtub as well as place the brand-new bath tub, the task is much harder. In either case, the project is within a home handyman's skills, although you will need a helper to leave the old tub and set in the new one. Make sure you have qualified on your own for the work and also fit trying it. As opposed to employing a specialist to take over a halfway-completed project, it is far better to take into consideration utilizing one before you begin. Opportunities are you might need a professional plumber to make tube links.
This write-up will certainly help you mount a brand-new tub in your bathroom if you have actually already acquired a brand-new tub and also do not need to alter the arrangement of your previous water pipelines.
Your tools and also product checklist need to make up the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is separate the water system. After doing so, turn on the faucets to drain any kind of water remaining in the system. The procedure of eliminating the existing faucets can be rather bothersome because of the limited access that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the taps. Have a cloth prepared for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. Once the faucets have actually been eliminated, the holes in the bath/basin will need to be cleaned of any kind of old securing compound.
Before proceeding to fit the brand-new faucets, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, then you will require a plastic adapter to prevent damages to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end gives a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly require decreasing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin making certain that the washing machines are in place between the faucet and also the sink. Safeguard the faucet in place with the producer offered backnut. When the faucet is firmly in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal tap connectors. The former type ought to be linked to the tap ends first, tightening only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Tub
Utilizing the two wooden boards under its feet, put the tub in the required position. The wooden boards are useful in evenly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 tiny factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be achieved by checking the level and also readjusting the feet on the tub up until the spirit level reads degree.
To mount faucets, fit the bottom of the furthest flexible faucet adapter to the proper supply pipe by making a compression join; after that do the very same for the various other tap.
Switch on the water supply and also inspect all joints as well as new pipework for leakages as well as tighten them if required. Fill the tub as well as likewise examine the overflow electrical outlet and the regular outlet for leakages.
Lastly, deal with the bath paneling as described in the maker's user's manual. Tiling as well as sealing around the bath tub ought to wait until the bath tub has been used at the very least once as this will certainly resolve it into its last setting.
Preparing for the Installment
First of all, the sustaining framework supplied with the bathroom should be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is necessary to ensure that if the faucet includes a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps device to prevent stress on the bathtub.
Fit the versatile tap ports to the bottom of both taps making use of 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make sure you use every one of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom must currently prepare to be suited its last placement.
Tiling Around the Bath tub
In the area where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall between the bath and also the tiling, leading to complications with dampness and feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your components and also installations. They are marketed in tubes as well as cartridges, as well as are capable of sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with spins of soaked newspaper or soft rope. Remember to always load the bath tub with water prior to securing, to enable the motion experienced when the tub is in usage. The sealer can break fairly early if you do not think about this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently offered on the market. It is suggested to fit the floor tiles utilizing water-resistant or water-proof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was shown that write-up about How to Install a Bathtub from a friend on a different site. Are you aware of someone else who is excited by the niche? Please feel free to share it. I appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Visit Our Site
Report this page